百度作业网英语翻译，急用，谢谢谢谢
来源：学生作业帮 编辑：百度作业网作业帮 分类：综合作业 时间：2024/07/16 09:33:27
英语翻译，急用，谢谢谢谢
The experiments of AISI S1 material are carried out satisfactorily and the results
obtained from the experiments were evaluated graphically and using ANOVA,
which is one of the statistical techniques.
During the high-speed finishing turning of hardened AISI S1 material, the best
results with regards to surface roughness were obtained with CBN cutters. The
increase in the feed rate value increased the roughness for both cutters. With
regards to turning operations, a roughness value of approximately 0.2 μm was
obtained, which is very good.
For both cutters, while the machining force increased depending on the increase of
the feed rate and cutting depth, it decreased depending on the increase of the
cutting speed With regards to machining force, CBN cutting inserts exhibited
better performance than ceramic inserts.
For CBN and ceramic inserts, the increase in cutting speed increased the flank
wear. With regards to flank wear, CBN cutter exhibited a better performance than
the ceramic cutter for the same cutting parameters.
According to the study of the SEM images, it was determined that effects of
slightly abrasive and intensely adhesive and diffusive wear mechanism are seen in
the ceramic cutter. For CBN cutting inserts, abrasive and intensely adhesive and
diffusive wear mechanisms are seen for the CBN cutters.
According to the ANOVA results, it was seen the change in progress levels is the
most effective parameter on surface roughness (Ra) statistically. It was shown that
the change of tool types did not lead to much change.
The experiments of AISI S1 material are carried out satisfactorily and the results
obtained from the experiments were evaluated graphically and using ANOVA,
which is one of the statistical techniques.
During the high-speed finishing turning of hardened AISI S1 material, the best
results with regards to surface roughness were obtained with CBN cutters. The
increase in the feed rate value increased the roughness for both cutters. With
regards to turning operations, a roughness value of approximately 0.2 μm was
obtained, which is very good.
For both cutters, while the machining force increased depending on the increase of
the feed rate and cutting depth, it decreased depending on the increase of the
cutting speed With regards to machining force, CBN cutting inserts exhibited
better performance than ceramic inserts.
For CBN and ceramic inserts, the increase in cutting speed increased the flank
wear. With regards to flank wear, CBN cutter exhibited a better performance than
the ceramic cutter for the same cutting parameters.
According to the study of the SEM images, it was determined that effects of
slightly abrasive and intensely adhesive and diffusive wear mechanism are seen in
the ceramic cutter. For CBN cutting inserts, abrasive and intensely adhesive and
diffusive wear mechanisms are seen for the CBN cutters.
According to the ANOVA results, it was seen the change in progress levels is the
most effective parameter on surface roughness (Ra) statistically. It was shown that
the change of tool types did not lead to much change.
符合美国钢铁协会的S1的实验材料进行令人满意的结果
从实验获得的图形和使用方差分析进行评估,
这是统计技术之一。
在高速完成车削淬硬AISI S1的材料,最好的
对于表面粗糙度结果用立方氮化硼刀具。的
进给速率增加刀具的粗糙度值增加。与
关于操作,粗糙度值大约0.2μm
了,这很好。
对刀具,加工力增加取决于的增加
进给速率和切削深度,它取决于的增加减少
切削速度对加工力量,立方氮化硼切削插入展出
更好的性能比陶瓷插入。
立方氮化硼和陶瓷插入、切削速度的增加,增加了侧面
穿的。至于侧面磨损,立方氮化硼刀具表现出更好的性能比
相同的陶瓷刀具切削参数。
根据SEM图像的研究,这是确定的影响
略磨料和强烈的胶粘剂和扩散磨损机制
陶瓷刀。立方氮化硼切削插入、磨料和强烈的粘合剂
立方氮化硼刀具的扩散磨损机制被认为。
根据方差分析结果,它被认为是进步的变化水平
最有效的参数对表面粗糙度(Ra)统计。结果表明,
工具类型的变化没有带来多大变化。
从实验获得的图形和使用方差分析进行评估,
这是统计技术之一。
在高速完成车削淬硬AISI S1的材料,最好的
对于表面粗糙度结果用立方氮化硼刀具。的
进给速率增加刀具的粗糙度值增加。与
关于操作,粗糙度值大约0.2μm
了,这很好。
对刀具,加工力增加取决于的增加
进给速率和切削深度,它取决于的增加减少
切削速度对加工力量,立方氮化硼切削插入展出
更好的性能比陶瓷插入。
立方氮化硼和陶瓷插入、切削速度的增加,增加了侧面
穿的。至于侧面磨损,立方氮化硼刀具表现出更好的性能比
相同的陶瓷刀具切削参数。
根据SEM图像的研究,这是确定的影响
略磨料和强烈的胶粘剂和扩散磨损机制
陶瓷刀。立方氮化硼切削插入、磨料和强烈的粘合剂
立方氮化硼刀具的扩散磨损机制被认为。
根据方差分析结果,它被认为是进步的变化水平
最有效的参数对表面粗糙度(Ra)统计。结果表明,
工具类型的变化没有带来多大变化。